GENERAL
BUILDING SPECIFICATIONS
Please note, these are the general building
specs for B.I.G. Booths. Many States require
modifications to these specs in order for
the booth to comply with individual State
requirements for Energy Code, as well as
State approval and third party factory
inspections. We urge you to call and speak
to a well informed
sales rep at B.I.G. to discuss your project.
FRAME
To be minimum A-500, 2" x 2" x .083
structural mechanical steel tubing, formed
for accuracy.
Advantages: Frameless appearance,
structurally superior to allow for
manufacturing up to 220mph wind load.
WALL SYSTEM
To be minimum of A-527, 16ga. cold rolled
galvanized steel interior and exterior
panels MIG welded between frame and mullions
for self aligning unitized system, insulated
to R-10.
Advantages: Superior strength and
durability, weather tight system.
ROOF
To be all steel construction, designed for
exterior use, insulated to R-19. Roof to
have fascia and\or overhang as indicated on
the drawings. Roof to be designed to drain
through a gutter system with downspouts and
to have a three part Energy Star membrane
coating with a Solar Reflective Index (SRI)
of 95 or greater. All booths that have roof
dimensions of 6' x 8' or larger have
removable lifting eyes for hoisting by
crane.
Advantages: Longer life in all
weather conditions, heat reflective and
energy efficient.
FLOOR
Unit to have R-10 insulated A-569, 11ga
steel plate floor covered with 1/8" x 19"
square industrial black rubber tiles and 4"
base cove. Floor system is welded to a 2"
steel tube frame and joists, with bitimous
under coating. Unit to have 1/4" steel
anchor plates welded to the interior side of
the floor frame with pre drilled holes for
anchoring of unit. Floor to have all
required cut outs for electrical, data &
communication stub-ups.
Advantages: Design flexibility for
specific site conditions such as ADA. Steel
framing and steel sub floor is structurally
superior and durable, rubber tile covering
is comfortable and long lasting.
DOOR
Unit to have one heavy duty steel framed
sliding door constructed of steel tube
frames and insulated 16ga. galvanized steel
panels. Door to be top hung by a minimum of
eight 2 1/4" steel ball bearing rollers in a
steel upper track with lower stainless steel
guide. Door to have stainless steel pull
handles welded to the frame and mortise hook
bolt lock.
Advantages: Steel doors are more
durable and standard for all booths, B.I.G.
is the exclusive provider of the rigid steel
ball bearing roller system with welded
stainless steel pull handles. Doors are more
aesthetically superior and offer years of
maintenance use.
WINDOWS
Unit to have steel window frame system with
flush mounted corners and welded fastening.
Unit to have fixed windows on all sides, all
windows to be glazed with 1/4" tinted
tempered glass.
Advantages: Galvanized steel frames
are more durable and Architecturally
Superior, less soot and dirt build up,
weather resistant and allows for easy
replacement of glass.
ELECTRIC
SYSTEM
To be all U.L. approved fixtures wired to
N.E.C. standards with 1' x 4' dual bulb
fluorescent lights with T-8lamps. Lights are
recessed in a 16ga. galvanized steel ceiling
painted to match the booth interior color,
and controlled by single pole wall switch,
two 115 volt 20 amp duplex outlet
receptacles mounted under the shelf.
All items to be wired to 125 Amp, 120\240
volt, 12 pole, 3 wire single phase load
center.
Advantages: Recessed lights offer
more head room and are Architecturally
superior, all booths come with bulbs, units
are pre-wired to meet code.
CONDUITS &
BOXES
In addition to the standard conduits and
boxes, unit to have two empty 2" x 4"
J-Boxes mounted under the shelf with 1/2"
empty conduit runs to the stub area for Data
& Communication lines by others.
Advantages: Provide raceways for typical
items added to booths on site, now the booth
already has these items ready for easy
installation.
SHELF
Unit to have one interior steel shelf
mounted on the front end wall. Shelf to be
20" deep mounted at 34" AFF.
Advantages: Shelf is welded in place
and provide for a minimum 250lb load.
AIR
CONDITIONER
Unit to have a commercial thought the rear
wall mounted unit that provides 11,800 BTU
cooling and 11,200 BTU electric resistance
heating at 230 volts. Booth to have a steel
shroud painted to match the booth and a
dedicated outlet.
Advantages: Through the wall mounted
air conditioners offer years of maintenance
free use and have good warranty. Better
heating and cooling capability vs. RV style
roof mounted units.
WEATHER
PROOFING
All seams and joints are to be pressure
bonderized, all openings to be fully weather
stripped. Roof to have three part membrane,
floor underside to be bitimous coated.
Advantages: Clean appearance, weather
resistant, floor under coating offers a
barrier between the concrete, roof coating
is energy efficient
FINISH
Unit to be electrostactically painted with
RUST inhibitive coating system. Using a High
build primer, and two part catalyst
polyurethane finish coat. Overall system to
have minimum 5 mil rating, and to carry a
minimum of 3500 hr. salt spray test. Color
to be specified by customer.
Advantages: Best coating in the
industry and the only one with documented
salt spray test on the same metal used in
the manufacturing. Computer color matching
available or select one of our 20 standard
colors
INSTALLATION
Units are shipped fully assembled, fully
wired, fully glazed and thoroughly painted.
Position units over electrical stub-up on
level pad. Drill and set 4 Expansion type
Anchor Bolts. Connect power and seal around
edges where the floor base meets the
concrete pad, and that's it. Careful
attention and coordination of electrical
stub-outs will save many man hours.
|
